OpenRD arrived
ページを編集するにはログインが必要です。
OpenRD がやってきた
[SYSTEM]と書かれているminiUSBをPCと接続。付属CDの[openrd-devkit-v1.0][openrd_host_swsupportpackage.zip]を解凍。[windows/openrd-ftdi-drivers/CDM 2.04.14_OpenRD]以下をインストール。
UTF8 TeraTermPro. を立ち上げ、シリアル接続。今回はCOM12らしい。
起動
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: OpenRD-Client LE
U-Boot 1.1.4 (Apr 22 2009 - 20:18:28) Marvell version: 3.4.16
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE80
Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Checking for BootROM Routine Errors
No. of BootROM routine retries: 8
NAND: Nand ECC error
Running POST...
DDR2 data bus test PASSED
DDR2 address bus test PASSED
UART 1 internal loopback test on baudrate 9600 PASSED
UART 1 internal loopback test on baudrate 19200 PASSED
UART 1 internal loopback test on baudrate 115200 PASSED
Device: 0, Size: 512 MB, Page Size: 2 KB, Block Size: 128 KB
NAND detection test PASSED
Bad Block: 0cc00000
NAND bad-block detection test PASSED
RTC test PASSED
6/6 tests PASSED
POST completed
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
Module 0 is AUDIO
Module 1 is RGMII
USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>>
Marvell>> printenv
baudrate=115200
loads_echo=0
ipaddr=10.4.50.165
serverip=10.4.50.5
rootpath=/mnt/ARM_FS/
netmask=255.255.255.0
console=console=ttyS0,115200
CASset=min
MALLOC_len=1
ethprime=egiga0
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
ethmtu=1500
eth1mtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
ethact=egiga0
ethaddr=00:50:43:01:DE:66
eth1addr=00:50:43:01:DE:67
run_diag=no
bootargs=console=ttyS0,115200 mtdparts=nand_mtd:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs) rw ubi.mtd=1,2048 root=ubi0:rootfs rootfstype=ubifs
bootcmd=nand read.e 0x800000 0x100000 0x400000; bootm 0x800000
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no
enaAutoRecovery=yes
Environment size: 1266/131068 bytes
Marvell>> boot
NAND read: device 0 offset 0x100000, size 0x400000
Reading data from 0x4ff800 -- 100% complete.
4194304 bytes read: OK
## Booting image at 00800000 ...
Image Name: Linux-2.6.22.18-dirty
Created: 2009-08-29 9:48:15 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2405724 Bytes = 2.3 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux...................................................................................................................................................... done, booting the kernel.
Linux version 2.6.22.18-dirty (jigar@localhost.localdomain) (gcc version 4.2.1) #1 Sat Aug 29 15:18:06 IST 2009
CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists. Total pages: 130048
Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs) rw ubi.mtd=1,2048 root=ubi0:rootfs rootfstype=ubifs
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 256MB 256MB 0MB 0MB = 512MB total
Memory: 514816KB available (4376K code, 365K data, 140K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 256MB
SDRAM_CS1 ....base 10000000, size 256MB
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e8000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
INTER_REGS ....base f1000000, size 1MB
NFLASH_CS ....base fa000000, size 2MB
SPI_CS ....base f4000000, size 16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size 2MB
Marvell Development Board (LSP Version KW_LSP_4.2.7_patch2)-- OpenRD-Client Soc: 88F6281 A0 LE
Detected Tclk 200000000 and SysClk 400000000
MV Buttons Device Load
Marvell USB EHCI Host controller #0: c095d600
PEX0 interface detected Link X1
PCI: bus0: Fast back to back transfers disabled
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: kw_clocksource clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
RTC registered
Use the XOR engines (acceleration) for enhancing the following functions:
o RAID 5 Xor calculation
o kernel memcpy
o kenrel memzero
Number of XOR engines to use: 4
cesadev_init(c0011674)
mvCesaInit: sessions=640, queue=64, pSram=f0000000
Warning: TS unit is powered off.
MV Buttons Driver Load
squashfs: version 3.3 (2007/10/31) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
NTFS driver 2.1.28 [Flags: R/W].
JFFS2 version 2.2. (NAND) Ac 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
XGIfb: Options <NULL>
XGIfb: Relocate IO address: 1000 [00001030]
XGIfb: Enable PCI device
XGIfb: Video ROM usage disabled
XGIfb: SR14=0 DramSzie 200000 ChannelNum 1
XGIfb: Framebuffer at 0xe8000000, mapped to 0xe0c00000, size 2048k
XGIfb: MMIO at 0xec000000, mapped to 0xe0880000, size 256k
XGIfb: XGIInitNew() ...12345678910111215171818118218319202122232425OK
XGIfb: Memory heap starting at 4096K
XGIfb: Using MMIO queue mode
XGIfb: No or unknown bridge type detected
XGIfb: Default mode is 1024x768x16 (60Hz)
Console: switching to colour frame buffer device 128x48
XGIfb: Installed XGIFB_GET_INFO ioctl (80046ef8)
fb0: frame buffer device, Version 0.8.01
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
RAMDISK driver initialized: 20 RAM disks of 4096K size 4096 blocksize
Loading Marvell Ethernet Driver:
o Cached descriptors in DRAM
o DRAM SW cache-coherency
o Single RX Queue support - ETH_DEF_RXQ=0
o Single TX Queue support - ETH_DEF_TXQ=0
o TCP segmentation offload enabled
o Receive checksum offload enabled
o Transmit checksum offload enabled
o Network Fast Processing (Routing) supported
o Driver ERROR statistics enabled
o Driver INFO statistics enabled
o Proc tool API enabled
o Rx descripors: q0=128
o Tx descripors: q0=532
o Loading network interface(s):
o eth0, ifindex = 1, GbE port = 0
o eth1, ifindex = 2, GbE port = 1
mvFpRuleDb (dfdf0000): 16384 entries, 65536 bytes
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
Copyright (c) 1999-2006 Intel Corporation.
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
Integrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 1632 at 0x0cc00000
2 cmdlinepart partitions found on MTD device nand_mtd
Using command line partition definition
Creating 2 MTD partitions on "nand_mtd":
0x00100000-0x00500000 : "uImage"
0x00500000-0x20000000 : "rootfs"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
UBI: attached mtd1 to ubi0
UBI: MTD device name: "rootfs"
UBI: MTD device size: 507 MiB
UBI: number of good PEBs: 4055
UBI: number of bad PEBs: 1
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 4055
UBI: number of PEBs reserved for bad PEB handling: 40
UBI: max/mean erase counter: 1/0
UBI: background thread "ubi_bgt0d" started, PID 257
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v3.0
usb 1-1: new high speed USB device using ehci_marvell and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 7 ports detected
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
Linux telephony interface: v1.00
Marvell Telephony Driver:
Warning Tdm is Powered Off
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int32x1 98 MB/s
raid6: int32x2 114 MB/s
raid6: int32x4 123 MB/s
raid6: int32x8 111 MB/s
raid6: using algorithm int32x4 (123 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: measuring checksumming speed
arm4regs : 1089.600 MB/sec
8regs : 758.800 MB/sec
32regs : 904.400 MB/sec
raid5: using function: arm4regs (1089.600 MB/sec)
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
dm_crypt using the OCF package.
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mvsdmmc: irq =28 start f1090000
mvsdmmc: irq_detect=93
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.14 (Thu May 31 09:03:25 2007 UTC).
ALSA device list:
#0: Marvell mv88fx_snd ALSA driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size: 506507264 bytes (494636 KiB, 483 MiB, 3989 LEBs)
UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format: 4 (latest is 4)
UBIFS: default compressor: zlib
UBIFS: reserved for root: 0 bytes (0 KiB)
VFS: Mounted root (ubifs filesystem).
Freeing init memory: 140K
Mount failed for selinuxfs on /selinux: No such device
INIT: version 2.86 booting
Welcome to Fedora
Press 'I' to enter interactive startup.
Setting clock : Tue Jan 18 16:12:18 EST 2000 [ OK ]
Starting udev: [ OK ]
Setting hostname OpenRD: [ OK ]
Checking filesystems
Checking all file systems.
[ OK ]
Mounting local filesystems: [ OK ]
Enabling /etc/fstab swaps: [ OK ]
INIT: Entering runlevel: 5
Entering non-interactive startup
Starting sysstat: Calling the system activity data collector (sadc): Cannot open /var/log/sa/sa18: No such file or directory
[FAILED]
Bringing up loopback interface: [ OK ]
Bringing up interface eth0: [ OK ]
Bringing up interface eth1: [ OK ]
Starting rpcbind: [ OK ]
Starting NFS statd: [ OK ]
Starting RPC idmapd: [ OK ]
Mounting other filesystems: [ OK ]
Starting system logger: [ OK ]
Starting kernel logger: [ OK ]
Starting system message bus: [ OK ]
Starting sshd: [ OK ]
Starting xinetd: [ OK ]
Network Audio System Release 1.9.1
[ OK ]
Starting ConsoleKit: [ OK ]
[ OK ] crond: [ OK ]
Starting SMB services: [ OK ]
Starting Avahi daemon... [ OK ]
Fedora release 8 (Werewolf)
Kernel 2.6.22.18-dirty on an armv5tejl
OpenRD login: root
Password:
Last login: Sun May 28 08:18:12 on ttyS0
-bash-3.2# uname -a
Linux OpenRD 2.6.22.18-dirty #1 Sat Aug 29 15:18:06 IST 2009 armv5tejl armv5tejl armv5tejl GNU/Linux
-bash-3.2# cat /etc/redhat-release
Fedora release 8 (Werewolf)
-bash-3.2# chkconfig --list
ConsoleKit 0:off 1:off 2:on 3:on 4:on 5:on 6:off
avahi-daemon 0:off 1:off 2:off 3:on 4:on 5:on 6:off
crond 0:off 1:off 2:on 3:on 4:on 5:on 6:off
dhcpd 0:off 1:off 2:off 3:off 4:off 5:off 6:off
dhcrelay 0:off 1:off 2:off 3:off 4:off 5:off 6:off
gpm 0:off 1:off 2:on 3:on 4:on 5:off 6:off
haldaemon 0:off 1:off 2:off 3:off 4:off 5:off 6:off
ldap 0:off 1:off 2:off 3:off 4:off 5:off 6:off
lirc 0:off 1:off 2:off 3:off 4:off 5:off 6:off
lm_sensors 0:off 1:off 2:off 3:off 4:off 5:off 6:off
mcstrans 0:off 1:off 2:on 3:on 4:on 5:on 6:off
mdmonitor 0:off 1:off 2:on 3:on 4:on 5:on 6:off
messagebus 0:off 1:off 2:on 3:on 4:on 5:on 6:off
nasd 0:off 1:off 2:off 3:off 4:off 5:on 6:off
netconsole 0:off 1:off 2:off 3:off 4:off 5:off 6:off
netfs 0:off 1:off 2:off 3:on 4:on 5:on 6:off
netplugd 0:off 1:off 2:off 3:off 4:off 5:off 6:off
network 0:off 1:off 2:on 3:on 4:on 5:on 6:off
nfs 0:off 1:off 2:off 3:off 4:off 5:off 6:off
nfslock 0:off 1:off 2:off 3:on 4:on 5:on 6:off
nmb 0:off 1:off 2:off 3:off 4:off 5:off 6:off
rdisc 0:off 1:off 2:off 3:off 4:off 5:off 6:off
rpcbind 0:off 1:off 2:on 3:on 4:on 5:on 6:off
rpcgssd 0:off 1:off 2:off 3:on 4:on 5:on 6:off
rpcidmapd 0:off 1:off 2:off 3:on 4:on 5:on 6:off
rpcsvcgssd 0:off 1:off 2:off 3:off 4:off 5:off 6:off
rsyslog 0:off 1:off 2:on 3:on 4:on 5:on 6:off
smb 0:off 1:off 2:on 3:on 4:on 5:on 6:off
snmpd 0:off 1:off 2:off 3:off 4:off 5:off 6:off
snmptrapd 0:off 1:off 2:off 3:off 4:off 5:off 6:off
sshd 0:off 1:off 2:on 3:on 4:on 5:on 6:off
sysstat 0:off 1:on 2:on 3:on 4:on 5:on 6:off
udev-post 0:off 1:off 2:off 3:on 4:on 5:on 6:off
winbind 0:off 1:off 2:off 3:off 4:off 5:off 6:off
xinetd 0:off 1:off 2:off 3:on 4:on 5:on 6:off
xinetd based services:
chargen-dgram: off
chargen-stream: off
daytime-dgram: off
daytime-stream: off
discard-dgram: off
discard-stream: off
echo-dgram: off
echo-stream: off
nuttcp: off
rsync: off
tcpmux-server: off
time-dgram: off
time-stream: off
-bash-3.2#
-bash-3.2# ifconfig
eth0 Link encap:Ethernet HWaddr 00:50:43:01:DE:66
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:63 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:532
RX bytes:7626 (7.4 KiB) TX bytes:410 (410.0 b)
Interrupt:11
eth1 Link encap:Ethernet HWaddr 00:50:43:01:DE:67
inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:532
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:15
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:560 (560.0 b) TX bytes:560 (560.0 b)
-bash-3.2#
-bash-3.2# cat /etc/rc.local
#!/bin/sh
#
# This script will be executed *after* all the other init scripts.
# You can put your own initialization stuff in here if you don't
# want to do the full Sys V style init stuff.
touch /var/lock/subsys/local
#mdadm --create /dev/md6 --level=raid5 --raid-devices=4 --assume-clean /dev/sda5 /dev/sda6 /dev/sda7 /dev/sda8
#/usr/bin/cryptsetup.sh -c aes -h plain -s 32 -d /root/key create data /dev/md6
#mkfs.xfs -f /dev/mapper/data
-bash-3.2#
-bash-3.2# reboot Broadcast message from root (ttyS0) (Tue Jan 18 16:49:08 2000): The system is going down for reboot NOW! INIT: Sending processeShutting down Avahi daemon: [ OK ] Stopping ConsoleKit: [ OK ] Stopping sshd: [ OK ] Shutting down SMB services: [ OK ] Stopping xinetd: [ OK ] Stopping crond: [ OK ] Stopping RPC idmapd: [ OK ] Stopping system message bus: [ OK ] Shutting down kernel logger: [ OK ] Shutting down system logger: [ OK ] Stopping NFS statd: [ OK ] Stopping rpcbind: [ OK ] [ OK ] Shutting down interface eth0: [ OK ] Shutting down interface eth1: [ OK ] Shutting down loopback interface: [ OK ] Starting killall: [ OK ] Sending all processes the TERM signal... Sending all processes the KILL signal... Saving random seed: Syncing hardware clock to system time Unmounting pipe file systems: Please stand by while rebooting the system... Restarting system.
Keyword(s):
References: